Normal/typical plug loads are accounted for (inferred) automatically within FEDS. These values can be viewed and/or changed from the miscellaneous equipment inputs in maximum detail display. The data is based on major end-use load surveys for typical plug load levels and accounts for the typical levels of equipment loads in a given use-area type. For example, for an office building this will account for typical levels of things, such as computers, printers, copiers, clocks, vending machines, coffee makers, and kitchenette equipment.
Prices must be provided for all fuels being used in the buildings being modeled. In addition, prices may also be provided for fuels not currently being used for FEDS to consider those fuels in its economic calculations (e.g., to consider fuel-switching opportunities).
TIP—Watch units required for fuel price parameters! Electric energy prices are requested in ¢/kWh, while demand charges are in $/kW.
Yes. FEDS now models and evaluates lighting controls, including occupancy sensors. To model existing lighting controls, the user must select the appropriate "yes" response to the "Existing lighting controls?" input and review the existing utilization factors. To infer reasonable utilization factors for the controlled lighting, specify the appropriate space type for the space where the lights exist.
FEDS will also automatically evaluate the savings potential and cost-effectiveness of lighting controls where they do not currently exist. In this scenario, select "no–evaluate occupancy sensor" and identify the most applicable space type. In this case, the "existing" utilization factors identify the portion of time that the lights are currently on, while the "with controls" utilization factors will be used by FEDS to model the impact of the occupancy sensor controls. The "number of sensors required" is used by the cost model to identify how many sensors need to be installed to control the current lighting.
Each lamp and ballast modeled within FEDS has a rated life (specified in hours) associated with it. Actual replacement intervals are calculated within the model based on the light's modeled operating hours (based on utilization factors and occupancy schedules) and rated life of each component. When a lamp or ballast fails, FEDS accounts for the cost to replace the component by figuring both materials and labor requirements. These costs are tallied over the economic study period and reported as the non-annual maintenance cost. FEDS uses the non-annual maintenance cost along with energy and capital costs in determining which fixture can best provide the required level of service at the lowest life-cycle cost.
Exterior lighting, such as security or parking lot lights can be included in FEDS by selecting the exterior fixture location. This will set the heat to space to 0 and alter the calculation of utilization factors appropriate for typical nighttime operation.
Refer to Appendix G of the FEDS User's Guide. Ex: FL 2x4 4F40T12 STD2 = a 2-foot by 4-foot fluorescent fixture, with four 40 watt T12 (1.5 inch diameter) lamps, operated by two standard magnetic ballasts (designed to operate two lamps each).
Generally, it is best to specify the original purpose of the building as the building type, and then modify the use-area type to reflect its current use. Select building type = "Education", use-area type = "Office." The building's construction characteristics are inferred based on building type, while usage parameters (including occupancy, lighting and equipment use, and hot water demand) are based on the use-area type.
There is effectively no limit to the number of building sets allowed in a single case if there is enough hard drive space. Currently, each building set occupies approximately 4.3 megabytes of space across all file types. Given adequate storage space, FEDS can be—and has been—used to model an entire community, city, or utility service area.
There is no real limit to the number of buildings that can be modeled in a building set. However, building sets are designed to model buildings that share similar characteristics. The more similar buildings are within a given building set, the more accurate the results will be.
Use the building type or use-area designation that best fits regardless of which list it is on. The building set classes were grouped this way to aid in the selection of common types, but either list may be selected.
The utilization factors for lighting represent the portion of time particular lights are on, on average, over the building set. They are expressed as a fraction of the maximum possible load (i.e., 100% of the lights are on 100% of the time) for a given time period. FEDS infers the occupied and unoccupied period utilization factors based on what is typical on average for the lighting technology and use-area type. FEDS typically assumes that some lights are on even during unoccupied times for security, safety, or cleaning staff, or simply because lights were left on. During seasonally unoccupied months and other periods defined as non-operating, utilization factors are set to 0 for all lighting records except for exit lights, which are assumed to operate constantly.
Typically, the "Other" fuel type represents liquid propane gas (LPG) or propane fuel. However, if you use another fuel type that is not listed (e.g., wood chips), you may use "Other" to represent this fuel type.
FEDS allows a negative value for percentage of heat to the conditioned space. For example, if the equipment has a COP of 2.0 and operates with an exterior condenser, then -200 should be entered for this value and the capacity should be half the actual rated capacity. (This will result in heating an amount equivalent to 200% of the unit's consumption as being rejected outside.)
A minimum or contract demand is included in some commercial and industrial electricity tariffs. It specifies the minimum billing demand that will be charged each month. This is important to understand because implementing energy efficiency projects that reduce the site’s monthly peak demand below the contract demand will have limited return, as no additional savings in demand charges will accrue once the actual monthly demand falls below the minimum contract value. If that is possible for your site, it is best to review this with your utility and negotiate a lower contract demand.
A demand ratchet is a billing method commonly imposed by electric utilities on large commercial or industrial customers. It specifies that the billed demand level in kW be the larger of the actual peak demand for the billing period, or a percentage of the highest peak reached during the previous X months. A typical demand ratchet uses 80% of the peak demand occurring during the previous 11 months as the comparison point. Under this scenario, if your facility experiences a peak demand of 1,000 kW for one hour (or 15 minute interval) you will be billed for a minimum of 800 kW during the next 11 months, even if your actual demand is much lower. Demand ratchets are generally used by utilities to reduce the risks of serving certain types of customers who have potentially large swings in demand during the year—making them pay for the assurance of having the high capacity available when needed.
A marginal price is the price paid for the last increment of energy purchased. This should, therefore, exclude all fixed charges (e.g., the monthly customer or meter charge) and focus only on the costs that vary based on the amount of energy used. Some rate structures are more complex and require some analysis. For example, in a block electric rate structure where users pay a certain amount depending on how much electricity used during the month, the value of electricity would be the price corresponding to the amount the building generally consumes in a month (rather than the average cost over all kWh's used). The marginal rate is the value of a unit of energy saved (i.e., the value of a kWh saved by an efficiency measure).
Providing detailed marginal prices for electricity (including any time-of-day or seasonal variations, and the impact of demand charges and ratchets) is important as it can have a huge impact on the types and cost effectiveness of recommended efficiency measures, as compared with applying basic melded average rates.
Distillate oil is light fuel oil that has been further refined than heavier oils. Examples include #2 fuel oil and diesel fuel. Residual oil, as its name suggests, is the oil residue that remains after distilling out the lighter grade components. It is generally designated as #4, #5, or #6 fuel oil, is much more viscous than ordinary oils, and must be heated to allow it to flow and be burned.
The lighting use-area fixture density is the inferred fixtures per square foot and is based on typical lumen levels for different use-area types. It represents the average fixtures per square foot over the entire use-area (or building for single use-area buildings). Typically, the user will know the total number of fixtures in a use-area and can enter this and allow the software to calculate the fixtures per square foot.
The typical FEDS user will not have detailed information available regarding plug load levels in order to adequately model them and will need to rely on the inferred values. However, miscellaneous equipment records may be modified or added if a load is unusual or atypical of the use-area type, or has an extremely large load (or one that sees extensive use) that is above and beyond what would be considered typical. Similarly, a user may want to reduce the capacity density for some areas deemed to have a lower load density than typical for that type of space, or even delete entire records when there is no equipment in use of a given type.
Most fuels are valued in FEDS as delivered to the building or end-use. However, the value for district fuels at the building or end-use level are determined somewhat differently. For self-generated fuel types (e.g., central steam, hot water, or chilled water) FEDS calculates the value of the fuel from the inputs in the central plants and thermal loops module. For example, the average value of self-generated steam is calculated based on the energy price of the fuel consumed by the boiler at the central plant along with its conversion efficiency, value of auxiliary energy and chemicals and labor to operate the plant, plus thermal and leakage losses in the thermal loops that distribute the steam to the building. If the central steam plant has multiple distribution loops, the losses may be different and therefore each steam loop can have its own average value for the steam it delivers. For purchased central fuel types (purchased steam, hot water, or chilled water) the value of the fuel delivered to the installation boundary is entered on the "Non-Electric Energy Prices" screen, and then FEDS applies information on the efficiency of each distribution loop to determine the average value of the steam at the building level as delivered by each loop. Marginal values do not consider fixed O&M costs (i.e., those that do not vary with the quantity of central fuel produced/delivered) or distribution losses (which are fixed and do not vary with the amount of energy delivered). Marginal values are used to determine the value of each increment of energy consumed or saved.
No. At this time FEDS considers only fixture per fixture replacements that provide similar light output. However, the energy impact of correcting an over/under lit condition could be analyzed comparing by two consecutive FEDS baseline runs (by running without optimization).
No. Given the importance of energy prices on the analysis, as well as the significant variation in rates available within a given region, there are no default or inferred electric or non-electric fuel price data. Users should enter the value of all fuels available.